DLink Firmware 2.14.04 Never Loads? Let’s Help!

DLink firmware 2.14.04 never loads? Are you facing this issue? If yes, then this blog can be of great help to you. Here, we have jotted down the tips that can help you rectify the issue in matter of minutes. Let’s get started!

Why DLink Firmware 2.14.04 Never Loads?

Before we make you familiar with the fixes to troubleshoot the problem,, we want you to be aware of the reasons that have led to the issue. Keep scrolling down!

• You are not connected to the WiFi network of your DLink range extender
• No connection between your router and WiFi extender
• The firmware process got interrupted
• You are loading the wrong firmware file
• Poor internet connection
• Technical glitches

That’s all! These were the reasons that cause the problem stating DLink Firmware 2.14.04 never loads. Let’s dig a little deeper and know how to deal with this problem in a flash.

DLink Firmware 2.14.04 Never Loads [Fixed]

Restart Your DLink WiFi Extender

You can try this easy fix to troubleshoot the problem. Yes, restarting is one of the easiest fixes to deal with any problem related to your DLink extender, including the one you are currently facing.

Follow the instructions highlighted below and know how to get the extender restarted in minutes:

• First and foremost, unplug the extender.
• Wait for a few minutes, approximately 4-5 minutes.
• Plug in back the extender, turn it on, and wait for its power LED to become solid

Try to load the firmware of your extender again. We hope that this time you get success. If not, then head over to the next section.

Connect to Your Extender’s WiFi

To load a firmware file without any hassle, you must be connected to your extender’s WiFi. What you have to do – open a desktop or laptop, click on WiFi icon, select your extender’s WiFi from the list, and connect to the SSID (network) using the password. However, you can also connect a wired source between your devices. How? Insert its one end into your extender and other end into your desktop/ laptop.

After connecting to the DLink extender, see if you are able to load the firmware or not.

Make a Connection between Extender and Router

No connection between your WiFi extender and router may not let the firmware to load. Hence, connection between the devices is very important.

How to connect router and extender?

By using an Ethernet cable. For this, you must have one more Ethernet cable handy. And, after having it, connect your devices in the same manner like you have connected your extender and desktop/ laptop.

Wait for the Firmware to Load Properly

The firmware files takes time to load. Chances are you have interrupted the process and that is why you are facing DLink firmware 2.14.04 never loads problem. Don’t worry! Log in to your extender using dlinkap.local (extender’s default web address), access the firmware update page, and follow the instructions on how to load the firmware file in a hassle-free way.

A few points to consider:

• While the process is going on, do not turn off your extender or disconnect it from your router.
• Also, you must not turn off your desktop or disconnect it from your extender’s WiFi.
• Do not go online or click on any link.

In accordance to the above-mentioned points, we really hope that you rack up success and load the firmware while relaxing on your couch.

Load the Correct File

Maybe you are not loading the correct firmware as per the DLink WiFi extender model you have. For the DLink firmware 2.14.04 never loads problem to get fixed in a jiffy, you must ensure that you are loading the correct file.

Check Your Internet Connection

Poor internet may not allow the firmware to load. Just ensure that your internet connection is up-to-the mark. Also, you can contact your ISP and confirm everything is fine from his side.

Reset Your WiFi Extender

If none of the troubleshooting tips mentioned in this blog post helped you, then resetting would be the last resort. Consider this as the most effective yet useful remedy.

How to Reset WiFi Extender?

To reset the extender, you have to disconnect the devices that are connected to the range extender. Then, you have to locate the extender’s reset hole and press it using a pin or any similar object. Hold the reset hole for 9-10 seconds, and release it.

In this way, your extender will reset back to the factory default values. Now, you need to configure it from scratch.

How to Reconfigure DLink Extender?

We will provide you with the easiest way for configuring the extender i.e. using the WPS method:

• Keep your DLink WiFi extender and internet router pretty closer.
• Press the extender’s WPS button.
• Wait for 1 minute.
• Press the router’s WPS button.

Your extender configures successfully using the WPS method. Now, log in to your extender using dlinkap.local web address and try to load the firmware on your extender again.

The Last Words

“Firmware” is software that needs to be uploaded on the extender regularly. This helps in enhancing the performance of the extender to a great extent. Now, we put a full stop on our writing. We hope that the dlink firmware 2.14.04 never loads problem you were fixing is now fixed by applying the troubleshooting tips highlighted in this blog post.